Instruction for transmission, gearboxes, rear axles (CB)

Highest effectiveness in use of Ceramizer® is obtained whencomplying strictly with recommendations and instruction.

  1. The technology is designed to protect new and regenerate  used mechanisms
  2. Ceramizer® can be used with all types of gear oil and for all types of transmissions and reducers.
  3. Lowered dose of Ceramizer® will not give expected results.
  4. Increased dose does not cause any side effects
  5. If any teflon or molybdenum components had been added to oil before, we recommend to exchange this oil and to clean mechanism before appying Ceramizer® . Otherwise its effectiveness will be reduced and process of the cermet creation will be lengthened.
  6. The ceramic layer lasts up to 2 years depending on the operating conditions of the mechanism (in normal operating conditions) or up to 100 000 km / 60 000 miles.
  7. Ceramization of worn surfaces can be repeated many times with Ceramizer®.
  8. Ceramizer® can be used for any devices (including industrial devices) after consulting Ceramizer’s® Producer.

 

DOSAGING  - amount of doses, needed for ceramization of friction surfaces presented below:

Capacity of oil in the gearbox (in litres) 1-2 l 2-5 l 5-8 l 8-11 l
Amount of doses 1 dose 2 doses 3 doses 4 doses

PACKAGE includes:

  1. Instruction of use.
  2. One dose of Ceramizer CB with net mass of 4 g

RECOMMENDATIONS:

  1. A characteristic symptom of early recovery  of the mechanism is  reduction of  noise after several tens of kilometers.
  2. In the case of significantly worn mechanisms and, in particular, if during the recovery after driving 100-200 km we see a slight improvement in operating mechanisms,it is recommended to double the dose of Ceramizer.
  3. In the event that after driving 100-200 km improvement of  the  mechanism is not noticeable - it could indicate an error in the assessment of component wear or mechanical damage to the machine.
  4. In the case of complex transmissions (powertrains) - it is recommended to double the dose of Ceramizer.
  5. In the case of gearboxes and transmissions used in motor sport and in extreme conditions, it is recommended to double the dose of Ceramizer.
  6. Apply at any stage of the mechanism operation, preferably directly at the oil change  to continue driving with Ceramizer for as long as possible.
  7. Use primarily for prevention to protect mechanisms against the effects of friction, significantly extending their service lifespan..
  8. During the whole process of ceramization (1.5 thousand km or 25 hours of work) do not replace oil.
  9. Use together with Ceramizer® for the engine, power steering and  fuel enhancer.

DIRECTIONS FOR USE FOR GEARBOXES, REAR AXLES:

  1. To obtain the best result, make sure that no teflon or molybdenum components have been added to oil recently (in case they were, it’s advisable to remove them from inside of the gearbox).
  2. Drive a few km (miles) to warm oil up.
  3. Turn the engine off.
  4. Unscrew the cap oil reservoir.
  5. Press out the content of syringe to the opening of oil infusion (make sure that required level of oil is maintained).
  6. Turn the cap oil back on.
  7. Drive up at least 10 km/6 miles with a speed lower than 90 km/h (56 miles/h) or 55 mph, then 100-300 m/ 0,5 mile on the reverse gear.

INSTRUCTIONS FOR USE FOR REDUCERS:

  1. Warm up oil in the reducer – keep the reducer going for at least 30 minutes.
  2. Turn the reducer off.
  3. Unscrew the cap oil reservoir of the reducer and pour the content of the syringe to the opening of oil inlet (make sure that required level of oil is maintained).
  4. Turn the cap oil reservoir back on.
  5. The metal-ceramic layer develops after about 60 hours in normal operating conditions. During this time oil exchange is not recommended.

WARNINGS:

  1. Do not apply to an automatic gear boxes or screw compressors.
  2. Do not apply  to differentials containing LSD mechanisms.

REMARKS:

  1. If any teflon or molybdenum components had been added to oil before, we recommend to exchange this oil and to clean mechanism before appying Ceramizer® . Otherwise its effectiveness will be reduced and process of the cermet creation will be longer.
  2. In case of any mechanical damages of the engine e.g. cracked or scorched piston ring, leaky valve, deep scratches on the cylinder etc., they should be repaired before adding Ceramizer®.
  3. Ceramizer® does not recondition any places where friction of rubber or plastic with metal parts occurs.
  4. The product is fully usable  even if a small leakage of product under the pusher is noticed.

SAFETY:

  1. This product is safe in accordance with the UE (91/155/EEC) norm.
  2. Store at a temperature below +40 oC. When the storage temperature exceeds 40 ° C the product can  sediment. Shake product and cool down to a temperature below 40 ° C to use it safely.
  3. Does not contain molybdenum or teflon.
  4. Keep away from children.

RESEARCH:

Effectiveness confirmed by multiple independent tests.

EFFECTIVENESS:

Ceramizer provides protection against wear and tear for minimum of 100 000 km / 60 000 miles. Ceramizer® can be used again after this mileage